Draw a room, set its wall height and estimate materials.
01 / PLANNING
Tell it what you can buy and what you need. It finds the layout that wastes the least.
Stock you can buy
Lengths at the store. Leave “on hand” blank for unlimited.
Most saw blades: 1/8″. Thin-kerf: 3/32″.
To square up rough or split ends.
For damaged factory edges.
Shorter leftovers count as scrap.
Type lengths any way you like: 8', 92 5/8, 7' 8 5/8" or 92.625.
Pieces you need
Name, finished length and how many.
Cut diagrams
How to cut each board
Measure from the left end. Red lines are saw cuts. Striped areas are leftovers.
Cut optimizer: lengths include one blade width (kerf) between pieces. Measure each mark from the trimmed left end and cut on the waste side of the line. Sheet layouts use straight, edge-to-edge cuts. Check your actual stock lengths and blade width before cutting.
Deck dimensions & construction
Enter the rectangular platform size and the materials in your plan.
Header, king studs, jack studs, sill and upper/lower cripples.
YOUR PLACE. YOUR NEXT PROJECT.
See the possibilities.
Add a photo of your house or yard, bring in your measurements, and describe the finish you have in mind.
$10 / pack3 pictures + 7 fixes · HD pack $15
1 Add your photo
2 Describe your project
3 Review & purchase
4 Make & fix pictures
Start with your space
A clear, wide photo helps keep the preview connected to your home.
Your photo goes here
Show the attachment point, nearby windows and enough ground to see the full project.
JPG, PNG or WebP · up to 10 MB. Your photo stays on this device until you choose Generate.
For a useful preview
Photograph the whole area in daylight. Include the existing roof when planning a tie-in. Keep people, license plates and private details out of the frame.
Make the brief yours
Simple answers become a clear image description. You can edit it before generating.
Measurements are only included when you import them.
Review the description
Each new picture uses this description. Fixes change one finished picture at a time.
AI previews show appearance, not exact dimensions, structural capacity or code approval. Use the calculator’s measured drawings and your applicable plans for construction.
Your preview pack
3 new pictures and 7 fixes, one at a time. No subscription.
3new pictures in each pack, plus 7 fixes
Checking preview availability…
Save your private access code. It restores this pack on another device. Anyone with it can use your pack.
Pictures are made by AI, so results can vary. You may need to refine your description and use fixes to get the result you want. Credits expire 60 days after purchase. Refunds are decided case by case. By buying a pack, you agree to the Terms of Use.
A picture that fails gives its credit back. Retries are limited to prevent repeated charges.
Already bought a pack?
Your pictures
Not quite right? Describe a small change under a picture and press Fix. Every version is kept. For a big change, like raising the whole deck, make a new picture instead.
Images powered by Higgsfield
Set up your rail
All measurements in inches.
Lengths you type and the lengths shown are along the top edge of the rail.
Measure between the inside faces of the posts.
Square bottom end to the lower miter joint center.
Upper miter joint center to the square top end.
Extra is added once to each blank, for trimming and kerf. Finished dimensions stay unchanged.
SIDE ELEVATION
How to measure & set your saw
Lay the broad face shown in the drawing flat on the saw table, with the straight long edge against the fence. Miter 0° means square across the stock. Blade bevel is 0° in this orientation. Use the cut-detail view to match the cut direction; settings shown are magnitudes.
For post joints, the span is the horizontal distance between inside post faces, not post centers. Both finished cuts are plumb. The vertical → sloped → vertical option starts at the square bottom of the lower vertical, meets the slope at J1, then turns upward at J2. In tread-mounted mode the upper vertical returns down to its tread instead. Inputs describe finished tread planes and the rail top above each mounting center; the planner derives joint-center heights and slope. Mounting offsets must keep each full-width foot on its tread. Anchors, base plates and guard/handrail compliance require the project detail. In free-path mode, the run is measured horizontally between J1 and J2; each vertical length runs from its square outer end to the joint center. Other modes start at a square outer end; connector and landing measurements run between centerline intersections. Equal-depth rectangular stock, all in one plane.
Finished edge lengths exclude gaps and kerf. The minimum blank covers both extreme tips; the selected extra is added for trimming. Check actual saw travel, field fit and a scrap joint before final cuts. Compound turns, copes, round rails and bracket-specific allowances are not modeled.
Flat broad face on table; bevel 0°. Miter measured off square. Equal rectangular stock in one plane. Post span is inside face to inside face. Other lengths are centerline intersection to intersection. No fitting gaps included. Dimensions govern; drawing is not a full-size template. Confirm with a test joint.
Stringer cut layout
Notched board, with the highest tread one riser below the landing.
STRINGER / SIDE VIEW
Stringer cut references
Mark the broad face with a framing square. Blade bevel remains 0°.
Cut
Cut-line dimensions
Angle to long edge
Off-square reference
Blade bevel
Recommended layout & cutting sequence
Measure rise between finished surfaces. Set a framing square with stair gauges for the calculated rise and run.
Mark one sound, straight board, crown toward the tread notches. Confirm the remaining wood and support design.
Make the bottom adjustment for tread thickness and lower-floor finish. Mark the top plumb cut down from the back of the highest tread seat.
Cut and test-fit the first board’s ends before cutting every notch. Confirm level tread lines and equal finished first/last rises.
Support and clamp the stock. Use a circular saw for straight cuts, stop at the intersecting lines on both faces, and finish the corners with a handsaw. Do not overcut.
Use the checked first stringer as the pattern for the others. Follow the specified bearing and hanger detail.
The landing is the final step: tread seats = risers − 1. Finished tread surfaces are one uniform rise apart. This face-mounted model terminates the stringer at the back of its highest seat, one rise plus tread thickness below the finished landing. Landing framing is drawn schematically; no hanger, rim size or fastening schedule is designed.
Total run is measured between the stringer’s first-riser plane and top attachment plane. Treads are shown without nosing and riser-cladding offsets. Lower floor finish means the height of the final walking surface above the stringer’s bearing surface. Tread thickness is included in both end calculations. The board’s original upper edge touches the front corners of its tread seats.
The displayed remaining wood, bearing line and blank envelope are geometry only. Choose the stock, spans, number of stringers and support detail from applicable plans/manufacturer guidance. A tread below a shallow rim may need a designed hangerboard or other backing. Do not trim the top seat shorter just to fit a connection. The base cut must be supported over the required bearing area.
Face-mounted cut stringer: highest tread one finished riser below the landing. End cuts account for tread thickness and lower floor finish. Broad face flat; blade bevel 0°. Run is between riser/attachment planes, excluding nosing and cladding offsets. Remaining wood and blank dimensions are geometry, not structural approval. Verify first-stringer fit and specified supports. Do not overcut notch corners.
Common rafter & seat
Solid lumber. Actual board dimensions.
RAFTER / CUT LAYOUT
Rafter cut references
Broad face flat. Angles are measured off square.
FROM ROOF PLANE TO LOAD PATH
Know what each member does.
The cut geometry is only one part of a roof. Establish the support system, then lay out the members and their connections.
01 / THE FRAME
Rafters, joists & ties
Rafters follow the roof slope. Ceiling joists span the ceiling; when properly connected and positioned, they can also restrain roof thrust. Rafter ties belong in the lower third of the attic. Collar ties sit in the upper third and address separation near the ridge; they do not replace the lower ties.
A ridge board is a meeting surface for opposing rafters. A structural ridge beam carries roof reactions to posts and foundations. An open porch without lower ties needs a designed support system.
The level seat rests on the plate; the plumb heel locates the rafter at the wall. Choose a supported seat length, then check the notch depth measured perpendicular to the board. Height above plate sets the rafter's upper roof plane.
The seat must not project beyond its support. Stop the saw at the notch intersection and finish the corner without overcutting. Check one rafter at the ridge, plate and fascia before using it as the pattern.
A hip is an outside roof fold; a valley is an inside fold. Jack rafters terminate at these lines instead of spanning the whole roof. At a square corner, equal pitches give a 45° plan line. Different pitches change the plan line, jack lengths, cheek cuts and backing on each side.
This planner solves a 90° corner bay with a common elevation datum. Its hip/valley length is the theoretical intersection line. The receiving ridge, support width, end joint and bearing determine final member cuts.
Equal overhang widths do not guarantee equal fascia heights. Compare the two roof-plane elevations, rafter depths and heights above plate. Backing bevels bring the top of a hip into the adjoining roof planes; a valley has the opposite fold.
Do not treat the plan angle, backing angle and cheek-cut bevel as interchangeable. The same roof has several different angles, each with a different reference surface.
A shed porch creates a slope transition in section. A perpendicular gable porch creates two valleys in plan. The porch tools use measured roof-plane elevations from one datum to find those intersections.
Overframed or blind valleys bear on an existing roof through sleepers and supporting framing. The selected rafter/jack cut detail gives cutting-plane angles. The mathematical intersection is not the sleeper's finished cut line: roofing build-up, member thickness and bearing shift it. Establish the actual support and verify it with a full-size layout.
Choose spans from the applicable loads, lumber species, grade, spacing, bearing and deflection criteria. Rafter span tables use horizontal projection, not the sloping cut length. A longer board is not automatically an adequate rafter.
Valleys and additions concentrate loads. Check the existing structure, snow/drift conditions, uplift connections, posts and foundations before attaching the new roof. A truss roof needs review for added overframing loads.
The solid-lumber birdsmouth tool does not apply to engineered I-joists, LVL or trusses. Some roof I-joist systems permit a specific low-end birdsmouth with required reinforcement; this is a manufacturer detail, not permission to notch any flange. Use the exact product's installation instructions and design.
Changing the porch pitch also changes the roofing detail. Asphalt shingles are not intended below 2:12; slopes from 2:12 to below 4:12 require special underlayment procedures. Follow the selected roofing system at valleys, slope transitions and wall intersections.
Framing a valley correctly does not specify its flashing. Plan drainage and the roofing build-up before fixing the final tie-in elevation.
Research reviewed November 8, 2026. Source editions and project examples have different scopes. The calculators provide dimensional layout, not structural sizing or local-code approval. Verify the adopted code and the product-specific support detail for the job.
Rectangle dimensions
Decimal feet.
PLAN / CORNER TO CORNER
Feet, inches & fractions
Use 5′ 3 1/2″, 7 3/4, or −2″.
Room outline
Place corners in order. One grid square = 1 ft.
Floor to ceiling. Used for every wall in this outline; estimate different-height sections separately.
Enter a wall height greater than zero.
Or click the grid to draw a custom outline. Corners snap to 6″. Undo steps back through your changes.
Edit the plan
Select: click a wall, door or window to edit it, drag corners and wall ends to move them. Walls: click where a wall starts, then where it ends. Door / Window: click on a wall. Everything is added to the estimate.
Optional: type the total length of interior walls you did not draw.
Upload a floor plan
The app reads the outside walls and interior walls from the picture, replacing any outline already here. Check them against the picture, then set the size. Works best with a clean, straight plan with dark walls.
Or trace it by hand
Use PNG, JPEG or WebP. To calibrate instead of typing the width: enter a known distance, then tap its two endpoints. The picture is saved with the project, along with the walls, doors and windows.
Sends the exterior perimeter and every interior wall to Materials. Subtract door and window areas there.
PLAN / 1 FT GRIDOPEN OUTLINE
Material estimate
Framing and sheet goods for the exterior and interior walls on this plan.
Prices (optional) — get a dollar total
Interior walls on this plan
Each wall is framed and gets drywall on both faces in the estimate.
Wall takeoff
Editable dimensions and waste.
What this estimate includes
Exterior and interior walls. Base studs at the selected spacing (plus one end stud per wall), one bottom plate, double top plate, and drywall by net area — exterior walls on the faces you choose, interior walls on both faces. Opening area is deducted once per wall face. Studs at openings, corners, headers, blocking, sheet layout and structural requirements are additional. Perimeter-based stud counts are approximate.
Project cut list
Saved snapshots from the handrail planner.
Editing the planner does not change saved cuts. Add a new set when dimensions change. Blank lengths include the extra selected when saved.
Add a task
Keep the next steps close at hand.
Punch list
Save your workspace
Measurements, room outline, cut list & tasks.
Saved in this browser. Export a backup to move devices or before clearing browser data. Imported projects open as a new working copy.
Your projects
On this device.
Construction Cut Pro · Geometry and estimating tools. Confirm site dimensions, materials and applicable plans before construction.